Slovenčina
English
Categories
- Automotive aerosol paints
- Touch up system
- Color code automotive paints
- Color code from VIN
- Step by step - refinishing paint
- Primers & fillers
- Clear coats
- Polishing
- Non aerosol paints
- Tuning line
- Chassis protection
- Sealing, bonding and lamination
- Appliances
- Tools and guides
- Abrasives
- Universal aerosol paints
- Degreasers and cleaners
- Colour Cards
- Lubricants
- Others
Mipa P99 Multi Star 250GR
Mipa P 99 Multi Star
PE-high build body filler
incl. hardener. For both filling and
finishing, for all metal substrates,
alu, zinc and fibre glass, beige.
7.50€
1K Epoxy primer grey 400ml MIPA
Aerosol WHEELSPRAY silver 500ml MOTIP
QUALITY AND PROPERTIES
- High-grade, quick-drying nitro-combi lacquer
- Good flow, smooth surface
- Weather-resistant, light-proof and non-yellowing
- Limited fuel-resistant
- Good colour and gloss retention
- Hard surface, abrasion-resistant
PHYSICAL AND CHEMICAL DATA
- Basis of the binder: acryl resin
- Colour: silver, gold, white, steel
- Smell: solvent
- Degree of gloss (at measurement angle 60° acc. to DIN 67530):
satin matt: 40-50 gloss units
80 - 90 gloss units after coating with MoTip Rallye Clear Coat glossy - Efficiency:
Depending on consistence and color of the ground:
150 ml are sufficient for 1 rims
500 ml are sufficient for 4-5 rims - Drying time (at 20°C, 50% relative air humidity):
Dust-dry: after approx. 5-10 minutes
Tack-free: after approx. 10-20 minutes
Cured: after 24 hours
Coatable with clear lacquer: after approx. 2 hours
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat. - Temperature-resistant: up to 110°C
- Storage stability:
10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) - Size:
aerosol cans with maximum nominal volume 150 ml resp. 500 ml
INSTRUCTION MANUEL
Before use, carefully read and observe the warning texts on the label!
Preparation of the ground:
- Carefully clean rims from dirt, fat and brake-dust.
- Treat existing pore rust with presto Deruster.
- The ground has to be sanded, clean, dry and fat-free.
- Mask off the rim edges with masking tape.
- Use paper to protect surrounding area from spray-dust.
- Prime with CAR's Primer.
- After drying, slightly sand (sanding paper grain P600).
Lacquering:
- The surface has to be clean, dry and free from rust and fat.
- Before use, shake the can vigorously for 2 minutes.
- Test spray to check colour-matching.
- Spray several thin coats in 3 - 5 minute intervals from a distance of approx. 25 cm.
- After 60 minutes drying time, coat with MoTip Rallye Clear Varnish to protect the metal pigments in the lacquer.
- Do not spray over synthetic paints!
7.94€
Aerosol WHEELSPRAY black 500ml MOTIP
QUALITY AND PROPERTIES
- High-grade, quick-drying nitro-combi lacquer
- Good flow, smooth surface
- Weather-resistant, light-proof and non-yellowing
- Limited fuel-resistant
- Good colour and gloss retention
- Hard surface, abrasion-resistant
PHYSICAL AND CHEMICAL DATA
- Basis of the binder: acryl resin
- Colour: silver, gold, white, steel
- Smell: solvent
- Degree of gloss (at measurement angle 60° acc. to DIN 67530):
satin matt: 40-50 gloss units
80 - 90 gloss units after coating with MoTip Rallye Clear Coat glossy - Efficiency:
Depending on consistence and color of the ground:
150 ml are sufficient for 1 rims
500 ml are sufficient for 4-5 rims - Drying time (at 20°C, 50% relative air humidity):
Dust-dry: after approx. 5-10 minutes
Tack-free: after approx. 10-20 minutes
Cured: after 24 hours
Coatable with clear lacquer: after approx. 2 hours
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat. - Temperature-resistant: up to 110°C
- Storage stability:
10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) - Size:
aerosol cans with maximum nominal volume 150 ml resp. 500 ml
INSTRUCTION MANUEL
Before use, carefully read and observe the warning texts on the label!
Preparation of the ground:
- Carefully clean rims from dirt, fat and brake-dust.
- Treat existing pore rust with presto Deruster.
- The ground has to be sanded, clean, dry and fat-free.
- Mask off the rim edges with masking tape.
- Use paper to protect surrounding area from spray-dust.
- Prime with CAR's Primer.
- After drying, slightly sand (sanding paper grain P600).
Lacquering:
- The surface has to be clean, dry and free from rust and fat.
- Before use, shake the can vigorously for 2 minutes.
- Test spray to check colour-matching.
- Spray several thin coats in 3 - 5 minute intervals from a distance of approx. 25 cm.
- After 60 minutes drying time, coat with MoTip Rallye Clear Varnish to protect the metal pigments in the lacquer.
- Do not spray over synthetic paints!
7.94€
Silver chrome SET
High-glossy effect spray that gives a look similar to chrome to smooth surfaces. Suitable for all smooth surfaces, especially for designing rims, wheel trims, coatable plastic parts if appropriately primed.
With this product MOTIP DUPLI for the first time offers a chrome spray which is resistant to abrasion and to weathering.
An optimal effect will be achieved on a black surface, e.g. by pre-coating with MoTip Tuning Effect Primer.
Silver chrome is overcoatable with clear 1K or 2K varnish.
The set contains:
1 x 150ml aerosol Effect primer black
1 x aerosol SILVER CHROME 400ml
1 x antistatic cloth
For the use on metal, wood, glass, coatable hard plastics, stone. The use on the different surfaces requires the right primers, e.g Motip plastic primer for plastic parts.
If the surface is not varnished so do not treat with any polish !
Note:
The picture is just ilustrative, the products are available as single items
20.80€
2K Two component gloss varnish - aerosol 400ml MIPA
Two component varnish with high gloss.
Use:
It is suitable for minor refinishing works and also for whole part refinishing.
Quality:
- high gloss result
- high UV protection - non yelowing
- high resistance against weather. mechanical and chemical stresses
- resistance against petrol and diesel !
- good atomisation
- safe and clean application of the included hardener
Drying times:
- dust dry: 10 - 15 min.
- touch dry: 4 hours
- completelly hard: 24 hours
- polishable: 8 - 9 hours
Pot life: 5 - 6 hours
16.50€
